MN103S83D internal ram 2 k-byte sram internal rom 64 k-byte type MN103S83D (under development) minimum instruction execution time 25 ns (at 4.3 v to 5.5 v, 10 mhz internal regulator used) 25 ns (at 3.0 v to 3.6 v, 10 mhz) *at internal 4 times oscillation used) package qfp084-p-1818e *lead-free maf00014aem interrupts ? 9 external interrupts 40 internal interrupts (watch dog timer, timer, serial i/f, pwm, a/d, system error) timer counter eight 8-bit timers interval timer, event counter, cascading four 16-bit timers interval timer, event counter, pwm output, double buffer watch dog timer serial interface tow uart (full duplex) / synchronous interfaces selective i/o pins exclusive: 5, selective: 45 i/o a/d inputs 10-bits, 2 inputs: 2, 6 inputs: 1 minimum conversion time 1.5us selective: 10 input 50 10 pwm 3-phase pwm output 16-bit counter, triangular waveform or jigsaw waveform dead time setup, double buffer
MN103S83D maf00014aem pin assignment qfp084-p-1 818e * lead-free qfp084-p-1 818i * lead-free support tool flash memory built-in type type mn103sf65gbf (under development) rom 128 k-byte ram 4 k-byte sram minimum instruction execution time 25 ns (at 4.3 v to 5.5 v, 10 mhz internal regulator used) 25 ns (at 3.0 v to 3.6 v, 10 mhz) package qfp084-p-1818i *lead-free on board debugger px-odb103s-do in-circuit emulator px-ice-103s52 1 2 3 4 12 9 11 5 6 7 8 10 13 14 15 16 21 17 18 19 20 29 22 23 24 25 26 27 28 33 34 35 36 43 42 37 38 39 41 40 44 45 46 47 53 55 52 48 49 50 51 54 56 57 58 59 60 61 62 63 84 83 82 81 76 75 74 80 79 78 77 p76/ irq02 p77/ irq03 64 69 68 67 65 73 72 71 p64/ pwm12 n.c. p81/ adin01 p82/ adin10 p66/ pwm14 p67/ pwm15 vs s p65/ pwm13 p74/ irq00 p75/ irq01 vdd p83/ adin11 p84/ adin20 p85/ adin21 p86/ adin22 p87/ adin23 p90/ adin24 lo n test3 osco p91/ adin25 30 31 32 p21/ sbi2 p13/ irq07 p14/ irq08 p17/ sbo2 p20/ sbt2 n.c. p43/ tm9bi p42/ tm9ai p41/ tm8bio p40/ tm8aio p32/ tm2io p34/ tm4io p33/ tm3io p37/ tm7io p36/ tm6io p35/ tm5io vdd vs s p31/ tm1io p30/ tm0io n.c. p27 p22/ sbo1 p26 p25 p24/ sbi1 p23/ sbt1 p63/ pwm11 p62/ pwm10 p61 p60 n.c. p57/ npwm02 p56/ pwm02 p55/ npwm01 p45/ tm9bo p46/ tm10ai vdd p51/ tm10bo test1 test2 vs s osci pvdd pvss p07/ nrst 66 p10/ irq04 p11/ irq05 p12/ irq06 vdd2 vdd 70 p80/ adin00 vs s p50/ tm10ao p44/ tm9ao p54/ pwm01 p53/ npwm00 p52/ pwm00 vdd2 vp p p47/ tm10bi MN103S83D mn103sf65gbf
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general elec- tronic equipment (such as office equipment, communications equipment, measuring instruments and house- hold appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus- tion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifica- tions satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rat- ing, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
